室內消防氣體（鹵代烷）滅火系統管道及設備安裝工藝技術交底.doc
進入下載頁
交底內容：
室內消防氣體（鹵代烷）滅火系統管道及設備安裝
1 范圍
本工藝標準適用于重要機房、珍藏庫、檔案庫等建筑。室內消防采用鹵代烷氣體滅火系統管道及設備安裝工程。鹵代烷滅火劑具有不導電、不污染特點，但只有在密閉空間中才能取得良好效果。
2 施工準備
2.1 材料設備要求：
2.1.1 室內消防氣體（鹵代烷）滅火設備、鋼材、管材、管件、各類閥件及附屬制品零配件等，應有出廠證明書及產品合格證。進入現場后，安裝使用前做檢查、驗證工作，必須符合國家有關規范、部頒標準及消防監督部門的規定和要求。
2.1.2 按照施工安裝進度計劃核對進場后的材料數量，檢驗其規格、型號、尺寸、質量是否符合設計圖紙要求。
2.1.2.1 鍍鋅碳素?zé)o縫鋼管及管件：
a 管材：采用鍍鋅碳素?zé)o縫鋼管或加厚鍍鋅碳素鋼管，管壁內外鍍鋅均勻，無銹蝕，內壁無卡筋，管壁厚度應符合設計要求。選擇管材時，內部經受的壓力應滿足設計要求。
b 管件：采用鍛壓鋼件內外鍍鋅，鍍鋅層表面均勻，無銹蝕、無偏扣、亂絲、方扣、絲扣不全、角度不準等現象。特別是法蘭盤要內外鍍鋅，鍍鋅層完整，水線均勻、不得有斷裂、粘著污物等現象。
2.1.2.2 有色金屬管道及管件：采用無縫銅管道及管件，管壁厚內外均勻，管皮內外表面光澤平滑，管件不得有絲扣不全、角度不準、偏扣、亂絲等現象。
2.1.2.3 閥件：閥件到貨后，要做抽樣實驗，應無裂紋、鑄造外型美觀、內外規矩、開關靈活嚴密、手輪無損壞。
2.1.2.4 設備：鹵代烷氣體鋼瓶、起動裝置箱及箱內附屬設備及零配件的規格、型號、尺寸、質量必須符合設計要求，其設備的零配件應齊全，外觀表面規整，無損傷。搬運時戴上瓶蓋，不能倒置、沖擊，慎重操作，不允許放在日光下直射及高溫、附近有
Cards on the table contents:
Indoor fire gas (Halon) fire extinguishing system piping and equipment installation
1 Scope
This technology is applicable to the important rooms, collections library, archives and other construction. Indoor use of Halon gas fire extinguishing system piping and equipment installation. Halon fire extinguishing agent is not conductive, non-polluting characteristics, but only in a confined space can be achieved good results.
2 construction preparation
2.1 Materials and equipment requirements:
2.1.1 fire service gas (Halon) fire-fighting equipment, steel, pipe, pipe fittings, valves and ancillary products, all kinds of spare parts, etc., should have certificate of origin and product certification. Entered the scene, so check before installation, validation, must conform to relevant norms, standards and fire protection departments ministerial regulations and requirements.
2.1.2 in accordance with the construction and installation schedule, after checking the amount of material approach, to test its size, type, size, quality, compliance with design drawings.
2.1.2.1 Carbon seamless steel pipe and galvanized pipe fittings:
a pipe: seamless steel pipe galvanized carbon or thicker galvanized carbon steel, galvanized inside and outside wall of uniform, no rust, no card inside wall reinforcement, the wall thickness should be consistent with design requirements. Selection of pipe materials, the internal pressure to withstand the design requirements to be met.
b tube: galvanized inside and outside by forging steel, zinc coating the surface evenly, no corrosion, no side buttons, random wire, side buttons, threaded incomplete, are not allowed to view such phenomena. In particular the flange to inside and outside the zinc, zinc coating integrity, uniform water line, not a fracture, adhesion dirt and so on.
2.1.2.2 non-ferrous metal pipes and fittings: The Road and the seamless copper tube, pipe wall thickness inside and outside the uniform, glossy surface inside and outside tube skin smooth, not a threaded pipe failure, angle allowed, partial deduction, random wire phenomenon.
2.1.2.3 valve: valve after arrival, to do sampling experiment, there should be no cracks, casting good looks, both inside and outside the rules, flexible and close switches, hand wheel without damage.
2.1.2.4 Equipment: Halon gas cylinders, starter boxes and ancillary equipment and spare parts box specifications, model, size, quality must meet the design requirements, spare parts for its equipment should be complete, the surface of neat appearance, no damage. Carrying, wearing cap, can not be inverted, impact, careful operation is not allowed on direct sunlight and high temperatures, near