鋼筋制作、安裝工程安全作業交底.doc

內容摘要：
1、 進入施工現場必須遵守安全生產的各項規章制度和紀律等。
2、 鋼筋斷料、配料、彎料等工作應在地面進行，不準在高空操作。
3、 搬運鋼筋要注意附近有無障礙物、架空電線和其它臨時電氣設備，防止鋼筋在回轉時碰撞電線或發生觸電事故。
4、 現場綁扎懸空大梁鋼筋時，不得站在模板上操作，必須在腳手板上操作。
5、 綁扎3m以上獨立柱鋼筋時，必須搭設操作平臺。
6、 不準站或坐在柱箍筋上綁扎，也不準將木料、管子、鋼模板穿插在鋼箍上作立人板。
7、 起吊鋼筋骨架，下方禁止站人，必須待骨架降到距模板1m以下才準靠近，就位支撐好后方可摘鉤。
8、 起吊鋼筋時，規格必須統一，不準長短參差不一，細長鋼筋不準一點吊。
9、 切割機使用前，須檢查機械運轉是否正常，有否二級漏電保護；切割機后方不準堆放易燃物品。
10、鋼筋頭子應及時清理，成品堆放應整齊，工作臺要穩，鋼筋工作棚照明燈必須加網罩。
11、高空作業時，不得將鋼筋集中堆在
Abstract:
1, into the construction site must comply with safety rules and regulations and discipline.
2, steel cutting, ingredients, materials, etc. should be bent on the ground were not allowed to operate at high altitude.
3, moving near the bar to pay attention to whether the barrier, temporary overhead lines and other electrical equipment to prevent the steel wires in the rotation when the collision occurred or electric shock.
4, left vacant spot beam steel banding shall not stand in the template to operate, must operate in the scaffold board.
5, 3m or more independent column steel banding must be erection platform.
6, allowed to stand or sit on the Binding column stirrup, or brigadier general timber, pipe, steel template inserted a steel hoop to make Liren board.
7, lifting steel frame, below the ban stand, must be dropped from the skeleton template 1m the following before they close, good support in place only after uncoupling.
8, lifting bar, the specifications must be unified, not allowed to vary in length, slender steel are not allowed to hang a little.
9, cutting machine before use, to check the machine is functioning properly, it has two leakage protection; cutting machine behind the combustible materials are not allowed to pile up.
10, reinforced head should be cleared up, finished products should be neatly stacked, tables should be stable, reinforced the work of studio lighting to increase the guard.
11, high-altitude operations, shall focus on the heap will be reinforced in
 

前往下載