瀝青路面瀝青灑布機作業-水泥混凝土路面施工安全技術交底.doc

交底內容   瀝青灑布車作業
檢查機械、灑布裝置及防護、防火設備是否齊全有效。采用固定式噴燈向瀝青箱的火管加熱時，應先打開瀝青箱上的煙囪口，并在液態瀝青淹 沒火管后方可點燃噴燈。加熱噴燈的火焰過大或擴散蔓延時應立即關閉噴燈，待多余的燃油燒盡后再行使用。噴燈使用前，應先封閉吸油管及進料口，手提噴燈點燃后不得接近易燃品。滿載瀝青的灑布車應中速行駛。遇有彎道、下坡時應提前減速，盡量避免緊急制動，行駛時嚴禁使用加熱系統。駕駛員與機上操作人員應密切配合，操作人員應注意自身的安全。作業時在噴灑瀝青方向10m以內不得有人停留。
瀝青灑布機作業
工作前應將灑布機車輪固定，檢查高壓膠管與噴油管聯接是否牢固，油嘴和節門是否暢通，機件有無損壞，檢查確認完好后，再將噴油管預熱，安裝噴頭，結實在油箱內試噴后，方可正式噴灑。裝載熱瀝青的油涌應堅固不得漏油，其裝油量要低于桶口10cm，向灑布機油箱注油時，油桶要靠穩，在油箱口緩慢向下倒油，不得猛倒。噴灑瀝青時，手握的噴油管部分應加纏舊麻袋或石棉繩等隔熱材料，操作時，噴頭嚴禁向上。噴頭附近不得站人，不得逆風扣作。壓油時，速度要均勻，海里突然加快，噴油中斷時，應將噴頭放在灑布機油箱內，固定好噴管，不得滑動。移動灑布機，油箱中的瀝青不得過滿。噴灑瀝青時，如發現噴頭堵塞或其他故障，應立即關閉閥門，等修理完好后再行作業。人工拌和作業應使用鐵壺或長柄勺倒油，壺嘴或勺口不應提行過高，防止熱油濺起傷人。
瀝青混合料拌和設備作業應遵守下列規定：
（1） 作業前，熱料提升斗、攪拌器及各種稱斗內不得有存料；
（2） 配有濕式除塵系統的拌和設備其除塵系統的水泵應完好。并保證噴水量穩定且不中斷。
（3） 卸料斗處于地下底坑時，應防止坑內積水淹沒電器元件。
拌合機啟動、停機，必須按規定程序進行。點火失效時，
Clarification at the content of asphalt distributor operations
Inspection machinery, spraying equipment and protection, fire prevention equipment is complete and valid. With fixed blowtorch to heat asphalt tank fire control, it should first open the box on the chimney pitch and submerged in the liquid asphalt only after the fire lit torch tube. Heating torch's flame is too large or spreading should be immediately shut down burner, the excess fuel to be burned and then OK to use. Blowtorch before use, should be closed and the inlet suction pipe, hand-held torch lit not close to combustible materials. Loaded with asphalt sprayer car speed should be in the running. In case of corners, downhill should slow down early to avoid emergency braking, when driving is prohibited to use heating systems. Drivers and machine operators should cooperate closely, the operator should pay attention to its own security. Asphalt in the direction of spraying during operation shall not be less than 10m people remain.
Asphalt distributor machine operation
Work before spraying machine wheels should be fixed, check the high pressure hose is firmly connected with the fuel injection pipe, nozzle, and the door is smooth sections, parts for damage, check to confirm well, the then preheat fuel injection pipe, install sprinklers, solid spray in the fuel tank test only after a formal spray. Loading hot asphalt oil Chung should be strong no oil leakage, the equipment is lower than the barrel oil export 10cm, sump oiling to the sprayer, the oil drums to rely on steady, slow down pour in the oil tank mouth, not fiercely down. Spraying asphalt, the hand of the fuel injection pipe section should be added the old sacks or wrapped insulation materials such as asbestos rope, operation, nozzle upward strictly prohibited. Sprinklers shall not stand near the person may not deduct for wind. Oil pressure, the speed should be uniform, the sea suddenly speed up, fuel injection is interrupted, shall nozzle spraying oil on the box and fixed the nozzle, not sliding. Mobile spraying machine, asphalt tank not too full. Spraying asphalt, if found to nozzle blockage or other failure, the valve should be closed immediately, well before making such repair work. Artificial mixing operations should be used iron pot or dipper pour oil spout or spoon I should not begin a new line is too high to prevent the hot oil splashes hurt.
Asphalt Mixing Plant operations shall comply with the following provisions:
(1) before the operations, enhance the thermal material bucket, blender and all that shall not have kept fighting materials;
(2) Wet Cleaning System with mixing equipment, pumps its dust removal system should be intact. And to ensure stable and does not disrupt water spray.
(3) Discharge hopper at the end of pit underground, should prevent the accumulation of water flooded the pit electrical components.
Mixing machine startup, shutdown, must be conducted according to prescribed procedures. Ignition failure,
 

前往下載